Table of Contents
- Why Use Belt Drive?
- Are There Any Downsides?
- Gates Belt Drive Models
- Belt Drive Frames: Rear Triangle Stiffness
- Belt Drive Frames: Belt Tensioners
- Belt Drive Frames: Splitters
- Belt Drive and Rohloff Hubs
- Belt Lines and Frame Clearance
- Gear Ratios
- Belt Drive and Tandems
- Maintenance and Cleaning
- Handling Belts
- Tensioning Belts
- Cost
- Belt Drive Touring Bike Manufacturers
Carbon Belt Drive has been developed over the last 30 years. It’s a power transmission technology used to run the blowers on 10,000 horsepower racing engines, the powertrains of 150 horsepower motorbikes, and more recently, the drivetrains of many bicycles.
The belts themselves are a series of nylon teeth that are reinforced using multiple carbon fibre cords. Belts are then paired with stainless steel cogs and durable alloy chainrings, which results in a super-tough chain alternative that will handle temperatures ranging from -65°F (-53°C) to +185°F (+85°C).
Belt drive is ideal because it’s very low maintenance and it offers 3-4X the service life of a chain. The reason it’s not more widespread in the bike industry is that belts cannot be used with derailleurs; instead, it’s limited to internally geared hubs such as Rohloff or Shimano, or crank-based gearboxes like the Pinion P1.18.
I’ve been using belt drivetrains paired with Rohloff 14-speed gear hubs since 2010. This has included a 31,000km (19,000mi) bike ride between Europe and Australia, my current 45,000km adventure from Argentina to Alaska and lots of multi-month tours in between. I started playing with belts on a modified Surly touring bike, later building up a custom Co-Motion tandem and am now travelling on a KOGA WorldTraveller-S touring bike.
Note: This article was originally published in May 2012 but has been completely overhauled Feb 2019.
Why Use Belt Drive?
![belt drive](jpg/hilite-pinion-belt-drive-80x47.jpg)
Belts Have A Long Service Life
You can expect a regularly cleaned belt drivetrain to last upwards of 30,000km/19,000mi. Additionally, belts will not rust if they get wet regularly (or are subject to salt near the beach).
Belts Require Little to No Maintenance
You don’t need to lubricate or degrease your belt. The most maintenance you’ll have to do is get a toothbrush and give the belt a scrub from time to time.
Belt Drivetrains Are Silent
You know when your chain is freshly cleaned and lubed and running perfectly silent? That’s a belt most the time (occasionally I need to apply silicone lubricant).
Belts Are Marginally Lighter Than Chains
You can expect a weight saving of around 100 grams when compared to chain drive. My drivetrain weight comparison is HERE.
Are There Any Downsides?
You Need A Belt Compatible Frame
As belts are one-piece, your frame will need to be designed with ‘belt splitter’ in the rear triangle. The frame will also need to be ‘stiffness test approved’ to ensure the belt cannot wander off the rear cog. When the rear triangle is particularly stiff you can actually run less preload tension on the belt, which results in less drivetrain resistance.
Belts Are Less Efficient Than Chains At Low Power Outputs
Belts have been tested to be less efficient than a chain drivetrain at low power outputs. That said, belts are likely to have an advantage when the conditions get nasty as all those chain links tend to accrue mud and grit (while a belt sheds it).
Replacement Parts Are Not Often Found In Shops…
… that said, with the high service life, you won’t need to obtain replacement parts often. It’s prudent to carry a spare belt (87 grams) to get you out of trouble on a bike trip (they fold up nice and small). I’ve never carried a spare chainring or cog as they’re very unlikely to be damaged even on a multiyear bike tour.
There’s A Higher Upfront Cost…
… but provided you get the full mileage out of your belt drivetrain, I’ve estimated you’ll go about 125km per dollar. This is the equivalent of a chain drivetrain costing you about $60 per 7500km (typical max distance for a chain).
Gates Belt Drive Models
CDX: High-Performance
The CDX High-Performance belt drivetrain is the most common belt option. You’ll find this model on almost all touring and adventure bikes. This system now has 16 belt lengths, 7 front sprocket sizes and 8 rear cog sizes to give you the most drive ratio options.
CDX: EXP
Gates more recently released an oversized version of the CDX drivetrain with 25% more surface area. This product is designed to get an even better range and durability, but still isn’t commonly found on touring bikes. There are currently five front sprockets and 4 rear cogs available.
CDN: Urban
The budget belt drivetrain from Gates is CDN Urban. The idea is to bring belt drive to city bikes in the €500 complete price range. These products are designed for the ‘casual rider’ and are not approved for use on mountain bikes, mid-drive eBikes, fixed gear bikes, or high mileage trekking/touring bikes. From what I’ve heard, people have had a few problems with the CDN rear cog, but they’ve all been upgraded to a cross-compatible CDX stainless cog.
Belt Drive Frames: Rear Triangle Stiffness
One of the most important factors for a belt drivetrain is that it is paired with a stiff rear frame triangle – and this is particularly important when carrying luggage on your bike.
On my older belted touring bikes I was able to generate enough flex through my frames to make the belts skip under load. But no matter how much power I put through my pedals on my KOGA WorldTraveller-S, I cannot get this to occur, indicating a higher degree of stiffness.
Stiffer frames also allow for lower belt tensions. As the “span tension” of a belt is higher than a chain at low power outputs, the lowest possible tension allows for the most efficient drivetrain. You can read more about belt drive efficiency HERE.
Gates offer a ‘stiffness test approved’ label to frames which pass their standard. But it’s worth noting that this is a minimum stiffness level, so some touring manufacturers do a better job than others to keep their rear triangle stiff. I recommend hunting for frames that use oversized tubes for the chainstays/seatstay section (my detailed article on frame stiffness is HERE).
You can find a list of every Gates approved frame HERE.
Belt Drive Frames: Belt Tensioners
A belt drivetrain requires a way to tension the belt. There are three different frame features that allow tensioning, each with their pros and cons.
EBBs: Eccentric bottom brackets allow you to move your crankset around 13mm forwards and backwards. The design also gives you the option to run your crankset high (nice for off-road) or low (better for the road). I’ve found EBBs a bit ‘creaky’ on long bike trips (more maintenance required) and additionally, they can get water in them, making them sometimes hard to adjust (again, maintenance required). The main upside is that companies like KOGA have tested EBBs to offer the stiffest rear triangle possible.
Sliding Dropouts: Sliding dropouts offer about 20mm of adjustment and are a great option because they are very easy to adjust. Like EBBs, you do not need to tension your belt every time you take your wheel out; it simply drops out and then slots back in at the perfect tension. The downside to these dropouts is that some lower-quality frames have the propensity to move forward using belts, resulting in inadequate tension.
Horizontal Dropouts: Belt frames with horizontal dropouts are rare. They’re not recommended by Gates as you need to set the belt tension every time you take your wheel out. That said, if you are using belts and horizontal dropouts, you’ll need a minimum of 10mm left in the dropout before the belt is tensioned – this space is required to get the belt onto the chainring.
Belt Drive Frames: Splitters
Unlike a chain, belts are one-piece, so a split in the frame’s rear triangle is essential. Splitters can be found in the seatstay, dropouts or sometimes even the chainstay. The most common splitters are integrated into the rear dropout, but some manufacturers have tested seatstay splitters to produce the stiffest possible rear triangle.
In the past, frames have been modified with splitters so that people can upgrade to belt drive. I no longer recommend making this modification because you simply can’t guarantee that your rear triangle will be stiff enough for a belt. Plus, there are so many dedicated belt frames out there nowadays which are similarly priced to the cost of a frame mod and re-spray.
If you still want to get this modification made, make sure to contact a reputable frame builder. I’ve used Ewen Gellie for my work in Australia. Cycle Monkey in Northern California (USA) can also make this modification.
Belt Drive and Rohloff Hubs
Belt drive combined with a Rohloff hub is a dreamy setup, but there are a few conditions attached. Not adhering to these may result in the partial loss of guarantee and warranty cover for your hub. But don’t worry, it’s easy to meet these conditions!
Firstly, your frames rear-triangle must withstand a minimum stiffness level. In short, bike manufacturers must prove frame stiffness levels on a specialist testing jig in order to be considered ‘stiffness test approved’. You can find a list of every approved frame HERE.
And the second condition is that you use a ‘belt snubber’. This product prevents the belt from walking off the cog under high load (or insufficient belt tension). When the belt lifts onto the top of the cog it can compromise the internal carbon fibres in a belt, so it’s recommended to use a snubber in any case.
Previously, belt cogs screwed directly onto Rohloff hubs, but now there is a much more user-friendly ‘splined carrier’ (part #8540L) with three splined belt cogs available (19t, 20t, 22t). This carrier makes cog changes much easier. There was a known issue for the 1st-generation splined carriers, but this was fixed mid-2018 (and warranty parts sent out), so won’t be an issue going forward.
Belt Lines and Frame Clearance
A straight ‘chain line’ or ‘belt line’ is absolutely essential for a properly functioning belt drivetrain (+/-1mm). The location of the rear cog is often fixed, so the majority of the adjustment will be at the crankset.
Belt Lines of various drivetrains:
– Alfine Di2: 39.8mm
– Alfine 8 or 11: 43.7mm
– Nexus 8: 44.35mm
– Nexus 7: 43.05mm
– Pinion C-Line: 52mm
– Rohloff 148mm, splined carrier: 51.7mm
– Rohloff 135/142mm, splined carrier: 54.7mm
– Pinion P-Line: 56mm
– Rohloff 170/177/190/197mm: 72.2mm
You’ll need to look up the chain line of the crankset you’re planning to use with your belt drivetrain. A triple 104BCD crankset has a 55mm chain line (when the chainring is mounted on the outside location), making them popular for Rohloff belted setups. It’s worth noting that Gates make their own cranksets with different beltlines to suit most belt drivetrains: 39.8mm, 43.7mm, 45.5mm and 54.7mm.
The other thing to mention is chainring clearance, in particular with Shimano hubs. As the gear selector on Shimano hubs is external and on the drive side, it results in a very narrow chain line. If a frame has inadequate chainring clearance at the chainstay, it may be incompatible with a Shimano hub. It’s worth getting in contact with a frame manufacturer to check on chainring clearance if you’re planning on using a Shimano hub with belt drive.
Gear Ratios
You might think that having fixed belt lengths reduces the ability to get your gear range right. But it’s worth noting that there are eight belt lengths and quite a few chainring and cog sizes, so the jumps between drive ratios aren’t large.
The Gates Calculator is a great tool to help determine which chainring and rear cog to use (this calculator is also available as a smartphone app). I find that if you plug in your optimal chainstay length (eg. 460mm) and hit ‘Find Solutions’, it will come back with the different combinations that will suit your frame first and foremost. You now just need to narrow down your ‘Gear Ratio’ options so they best suit your terrain. This will need to be done in accordance with the chainrings/cogs that are available for your Rohloff/Shimano/Pinion etc.
As mentioned above, if you are using belt drive and horizontal dropouts, you must have a minimum of 10mm left in the dropout before the belt is tensioned.
Belt Drive and Tandems
Belt drive is great for timing belts on tandem bikes. This saves you about 250 grams over the equivalent chain and chainrings. In order for belt drive to work on your tandem, your frames boom tube must be 724mm between bottom brackets. You’ll also need to be using 130BCD cranks. It is possible to run belts on both the drive and non-drive side of your tandem but the latter is recommended.
Maintenance and Cleaning
Belt drivetrains are almost maintenance-free. Cleaning is often as simple as rinsing the belt/cogs using a water bottle and an old toothbrush. No degreaser. No chain cleaner. No dirty hands.
The amount of work you do to maintain a belt will depend on the conditions you’re cycling through. In the driest, dustiest regions of the world, I’ve needed to apply a silicone lubricant to my belt every couple of days. Other times, its months between any maintenance or cleaning. While the belt system seems to do a pretty good job of removing mud and grit, you’ll want to keep the teeth of your belt as clean as possible to get optimal mileage.
Silicone Lubricant: I use a general-purpose silicone spray when I hear the first squeak from my belt. My current spray bottle was purchased from an automotive store in rural Bolivia, so I have no doubt similar products can be found all over the world. Gates recommend THIS heavy-duty silicone lubricant, in particular.
Handling Belts
You have to be careful with how you handle belts, as misuse can lead to internal carbon fibre damage… and trust me, you don’t want a snapped belt. The main thing is to ensure you don’t stress the fibres in any direction. If you’re storing a belt for a long time, it’s best to leave it fully open.
When installing your rear wheel, it is essential that you do not ‘crank’ the belt back on like you may with a chain. Instead, simply put the belt onto the chainring and cog, then slide your wheel into the dropout.
The great thing about belts is that they coil up nice and small so that you can easily carry them as spares. I generally tuck my spare belt into the pocket of one of my panniers. You’ll need to be careful folding and unfolding your belt – make sure you don’t force it, it should coil very naturally. When it’s folded correctly it should naturally sit in a loop which folds three times.
Tensioning Belts
Gates Carbon Drive tension will vary depending on whether you use a singlespeed or internally geared hub, and how powerful you are as a rider. There are a few different ways to get your tension to what Gates recommend.
Smartphone App: You can download a simple app which will measure how much tension your belt has with your smartphone microphone. Simply hold the phone next to the belt and give it a few plucks and it will quickly give you an average frequency rating.
Gates Tools (Sonic Tension Meter, Krikit Gauge): More accurate tension gauges can be found at specialist bike shops, but I’ve never needed to use these products.
Tension variation (tight spots) may occur when the crank is rotated, so Gates recommends taking several tension measurements at different crank arm locations to find an average. Around a 10lb or 15Hz variation is considered acceptable. If significantly more variation exists, Gates recommends centring the chainring on the crank spider.
Cost
CDX: High Performance
Chainring: US $70-110
Rohloff Cogs: US $93-105
Alfine Cogs: US $120-125
Pinion Chainring: US $154
Pinion Cogs: US $128-140
Belts: US $80-105
Kit Total Rohloff: from US $243
Kit Total Alfine: from US $270
Kit Total Pinion: from US $362
Belt Drive Touring Bike Manufacturers
Like the sound of belt drive? I’ve compiled a list of touring bike manufacturers HERE. For those wanting to do a custom build, my list of touring frame manufacturers is found HERE. Expect to spend more than US $1000 / €1000 on a complete belted bike and a minimum of US $500 / €500 on a belted frameset.
If You Have Any Further Questions, I Will Try My Best To Answer Them Below.
Belters are awesome! Team this up with a 14-speed Rohloff hub and you’ll be cruising. I love the idea of it being quiet, smooth and low maintenance. I’d like to build a bike in the future with a IGH and a belt drive combo.
We’re hoping to be able to tour around the world problem free!
I am driving a Rohloff + Centertrack for half a year now, but the rear cog is pretty much worn out. I do ride a lot of mud nowadays… On average you can say I maybe ride 40Km a week, that just isn’t much.
That sounds like it has worn a bit quick… we have both completed well over 5000km on our Centretrack drive trains with no noticeable wear on the rear cog. The front chainring is loosing its anodising now, it will be interesting to see how many kilometres we can get out of it. Are you using the stainless steel cog?
Awesome info, thanks! A question: do you know the difference between the CDX and CDC systems?
Hi Paul. The only difference between CDC and CDX is the width of the belt. CDC is 10mm wide and designed for city riding, and CDX is 12mm wide and designed for a MTB application. Having said that, make sure you ride Centertrack; it is leaps and bounds better than the older system. Alex
Hi Alex – I have been researching my next bike for a few months now, over which time I’ve read a lot about the Gates Belt Drive, and for some reason only just found your article today – it’s by far the most informative article on the system I have come across.
I initially loved the idea of the Belt Drive but was then put off the system after reading what Thorn, a British manufacturer of touring bikes, think of it. I’ve since come back around to the idea a bit but it still bothers me that I haven’t seen most of the serious concerns raised by Thorn fully addressed properly elsewhere – which makes me wonder whether either Thorn are scaremongering or Belt Drive sellers are more interested to tapping into the low-maintenance market than selling something they genuinely believe in.
The article can be found here http://www.thorncycles.co.uk/thornpdf/ThornLivingWithARohloff.pdf on pages 18 and 19. I’d be really grateful for your views on Thorn’s concerns, specifically:
1. The supposedly expensive, difficult to find and heavy tool for removing the rear Belt Drive sprocket (I have been unable to find much/any corroborating info about this elsewhere).
2. The apparently delicate nature of the belt, both during use and during maintenance for punctures etc (specifically, the damage caused from stones, twigs, knocking the drive with your legs or against a post. The Gates manual apparently says you need to “make sure that no components or objects can come into contact with the belt”, which sounds a bit daft in a daily use bicycle).
3. Potential weakening of the right-hand rear chainstay from the frame split.
Thanks 🙂
Hi Kieran
I’m glad you’re looking at belts as an option – we have been running our Centertrack kit for a long time now without issue. We are wondering when something will fail, but we consider ourselves good guinea pigs given that we ride in all-weather conditions in lots of different countries.
My guess is that Thorn haven’t spent a good amount of time on belts! Thorn are pretty well known for being staunchly for or against different things – disc brakes on tandems for example. We take their somewhat extreme reactions to certain matters with a grain of salt… 😉
1. Regarding the rear sprocket, we do not carry a tool to take it off. But we don’t carry a chain whip when riding a chain driven bike either. Yes, it will be harder to take off our cog when we need to (realistically the tool will get sent from Germany to wherever we are), but we are gambling on the rear cog making it a long way yet.
2. As mentioned above, we haven’t had any problems with with our belts… although we do cringe when multiple people per day twist our belts in their fingers. Intrigued locals like to give them a good yank, and still everything works fine. Delicate? No less delicate than a chain in our opinion.
3. The only frames we recommend buying should be ‘Stiffness Test Approved’. I don’t think you’ll have any issues at the chain/seat stay with an approved frame that has been tested with the correct tool.
Regards
Alex
Wow thanks for your quick, informative (and diplomatic! 😉 ) reply on a year-old post!! You have almost completely set my mind at ease, especially as I don’t expect to do any touring.
I say almost, as regarding your answer to q.1 – I hear what you’re saying when out touring but is it at least reasonably easy for a normal user to get hold of a tool when you’re at home living in the developed world?
We keep tabs on comments on the site, and like to reply as quick as possible – otherwise we get stuck with a backlog!
It would be worth finding out who has tools near you. Like Thorn mentioned in their article, there may only be only one shop in your country which has the right tooling. But really, you won’t need to worry about taking your cog off for another 20000km+ – so maybe carbon drive will be available in more bike shops by then!
Ahh OK – that’d probably be at least 5 years for me then so yes, hopefully the tool would be more available!
If I may ask a couple of other things – regarding the frame stiffness in point 3, I had thought that was more to prevent the chain tension changing from moment to moment as the frame flexes, rather than to certify strength or point of material failure. Since a stiff material/join isn’t necessarily a strong one or one with a long fatigue life, do you know if this test includes a strength/fatigue test?
(I accept too that the strength of the chainstay join is dependent on a given manufacturer’s design of the join, so maybe some are plenty strong enough while some aren’t – I imagine that if it’s as strong, say, as an S&S coupler, it shouldn’t be an issue. Also, if it was an issue, I’d have thought you’d have had a frame failure by now with all the travelling you’re doing on the Belt Drive.)
Also, on a slightly different thing, I have been pondering the use of drop bars with Rohloff; I want Rohloff ideally, but have been considering the Alfine 11 as the idea of having to move my hands from the drops/hoods whenever I want to change gear seems a bit annoying. Maybe it’s not that bad but I would anyway like to have interrupter levers on the tops for negotiating traffic etc. During initial discussions with one of the manufacturers that have made my shortlist, though, they didn’t think that interrupter levers are long enough to clear the Giles Berthoud/Co-Motion drop bar shifters and, sure enough, all of the few interrupter levers I can find do look rather stubby. Have you any experience with this? Do you think it’s a workable option? Do you know of any levers that would meet my requirements?
I hope I’m not taking advantage of your helpfulness & hospitality by asking yet more questions! Forums are of limited use when trying to get authoritative answers and it’s great to be able to get unbiased information from somewhere; having stumbled directly onto this page from google I only just realised that you’re in the middle of a tour of Europe and the Middle East. It’s amazing how you’re managing to run such a detailed blog while on the go!
You’re correct – the stiffness test is just a test of stiffness and that doesn’t mean the frame is strong. Never mind my point.
From all I’ve seen on the internet, which is admittedly too much, I haven’t seen failures at the seatstay joins on belt frames. This doesn’t mean a frame with a split can break, of course, but I don’t think this should be a concern given how many belt drive bikes are around these days. Get your frame/bike from a reputable manufacturer backed with a good warranty and you should never need to worry.
We love questions! We are glad to be able to help, whether it be from home or on the road.
What is the proper procedure for getting a cdc belt to track straight. Mine has a tendency to track 5mm to the inside while the small cog is tracking straight.
Thank you for a proper article. Their seem to be plenty of opinions
about but little in the way of solid research. I’ve only just started
looking into belts but defiantly more intrigued now.
Glad we can help.
Hi
I bought bike with a belt drive.
On one of mine trip I had a silly accident:
Other belt from mine bike-bag get between wheel and belt. I did not see what actually happen under me but mine bike was stopped immidetaly! I look what happen and carbon belt was out of sprocket. I notice also that the belt hurt a little from the external side. But it was in one peace. I spent some time to get the belt on sprockets again. I start pedaling and belt simply rip off.
Next I had very long walk.
With the first opportunity I start to search for a new belt.
Well … believe me that getting carbon belt in Norway is almost a miracle.
I contact with Gates (manufacturer) and they give me price 110euro for belt and delivery.
why the hell I choose belt ?
It last much shorter than mine last cheapest chain.
Hello Lukas
Sorry to hear of your bad experience. I suggest that you take a closer look at your belt alignment and tension. It sounds like something isn’t set up properly which had caused your belt to jump off.
We have now completed over 25,000km on our current belt and are really happy with the longevity of the product – we’ve certainly never got this kind of distance out of a chain! As the belt is so lightweight (80g), we always carry a spare with us.
Alex
Yeah … that’s mine bad experience.
But it was setup correctly in Germany just before the trip.
But I do not give up. Since it was sort of accident I will give the second chance to carbon drive 😉
Awesome write up Alex! And a great, inspiring website too.
I’m having a titanium touring/mountain bike frame made up with provisions for the addition of a belt drive but am a little concerned about the noise created by grit and dust that you’ve mentioned. On the gates website they recommend cleaning the belt with water, letting it dry then lubricating with a dry silicone spray which should repel dust and elevate the noise problem. Did you try this? I know in the automotive industry it’s a standard technique used to deal with noisy belts.
*alleviate. Pretty sure you don’t want to elevate the noise problem!
Surprisingly, we haven’t tried silicone spray! It seems that the places that are sandiest are also the most remote – but thanks for bringing this information to the forefront of my mind. Will have to test it out soon.
Hi Alee, I’m having hard time with Gates carbon belt system. Do you know if CDX and CDC system are exchangable? I’m asking because I was so pissed off with belt alignemt of CDC (after every ride I couldn’t manage to keep the belt perfectly in line) that I decided to go for CDX system. I haven’t finished to install everythings yet because it looks like there’s a misalignment of about 3mm on belt center line between CDX rear and CDX front cog, and I can’t figured out why this happen. I’ve just replaced the old parts with new ones. Thanks for your tips. Roberto
Hi Roberto. I am not too sure of the particulars, but once you’ve got it all installed you’ll be able to get a better idea for how much difference there might actually be in the chain line. You should be able to add or subtract chainring or bottom bracket spacers to get the alignment perfect. Alee
Hi Alee, thanks for your infos. I wish Gates Carbon (Europe) would have warned me when I asked them the ordering part number for the CDX having already the CDC system installed. Anyway, your info is really useful. I thook a photo to show you better the situation. I’ve placed a long ruler on the front pulley and measured the misalignment on the rear cog. I have 8,10mm from the center line that means more than 3mm of misalignment.in the chain line.
Now because the internal hub is a shimano Alfine I don’t think I can shift the rear side. Can I??
I’m not even sure if I can play with bottom bracket spacers because as default my bike is already mounting two spacers (5mm total) on the not-drive side (I guess to get chain line with the old CDC). According to your experience do you think will be possible to add a spacer of 3 mm?? The crankset is a Truvativ fireX GXP.
Last option adding 3mm chainring on the spider, but here I don’t know the nuts will hold such big lengh. Gosh I’m feeling on the edge of a divorce with belt system.
Thanks for your advice
Roberto
Hi again. We had a couple of millimetres difference in chain line from the CDC to CDX. From memory I added a few millimetres to the bottom bracket on the drive side. It will take a bit of trial and error to get it perfect, so give it time! I don’t think you’ll need to divorce your belt setup just yet. We’ve done 26,000km on our current cogs and belt – the Centertrack system is a great!
Hi Alee, finally I could untie the knot of the chain line. I bought longer bolt but because they where too long I had to add double spacer (that weren’t so easy to find for the right thickness). In photos you can see all the stuff I bought to fix this issue. Anyway now everything is installed and looks it is working really good.
Because of the money I have spent for the chain line system (CDC and CDX) and time installing it I wish I will ride more that 50000Km without touching anything anymore.
Thanks for your information. I hope that it will be useful also for others riders.
Roberto
Hi is there any lighter crank arm/set ?
I’m not sure what you mean. You can use cranksets from almost any manufacturer with Carbon Drive, even the lightest in the world.
Alee.
Great write up and your forum support looks exemplary too. I just imported a Single speed Cx bike from the US with CDX Centretrack. I was looking for a low maintenance commuter for my 14 mile jaunt into London every day and couldn’t find anything in the UK without paying a bespoke-build fortune.. I love it so far. I do wonder though about what seems to be a ‘reasonable’ amount of resistance I feel when hand cranking the pedal on the work-stand. Noticeable even if cranking backwards with no resistance from cranking the spinning wheel around. The tension is OK according to my iphone app. Is this resistance normal? There is no running noise. What is your experience please? There are no belters in the UK to compare notes with!
Any help welcome.
If it’s running the right tension, then my advice is to leave it. That said, we run our belts slightly lower tension to reduce the resistance – we can get away with it on the touring tandem because we don’t accelerate hard too often. If you’re ‘just cruising’ and not taking off at the lights like a madman, you can technically get away with less tension.
Hi Alee,
I have a new Surly Troll frame which is suitable for a Rohloff IHG as it has horizontal rear drop outs and OEM 2 mounting plate. Originally I wanted to fit a Gates CDX Belt drive but got put off not knowing whether it was stiff enough or finding a suitable frame builder to modify it to include a break in the rear seat stay or modify the drop out to allow a belt to be fitted. First off is the Troll frame stiff enough and secondly is it easy to modify it to include a break for the belt?
I plan to put a Rohloff OEM TS disc brake (solid axle) hub into my Troll frame and then ride around the world. But to keep the best clean I am going to try to fit a full chain guard as I can’t even be doing with the cleaning that might be involved riding in really dire roads.
Thanks in advance for your help.
Hi Alex
Regarding stiffness, I am not actually sure what chainstay and seatstay tubing is used on the Troll. Perhaps email Surly asking for tubing specifications? Or alternatively, bring your frame to a reputable frame builder to get their opinion on the matter. My initial thoughts are that the Troll would be a fine candidate, given that it is designed with pannier bags in mind…
I would suggest putting a frame break into the seatstay rather than modifying the dropout. The dropout should stay one piece…
Don’t forget to check whether your chainstay length will be ok for the ratio you are thinking of using. You need to have 10mm in the dropout in order to get the wheel out, so the axle needs to sit at 429mm or further on the Troll. I had a look at the Gates Calculator (http://www.gatescarbondrive.com/Apps/DriveCalculator/index.html) and it seems that you could run a 2.5/1 ratio (same us my touring bikes) with a 115t belt. That gets me up most climbs fully loaded!
Alee
Hi There,
Santos, a very reputable Dutch manufacturer of trekking bikes and tandems has tested both belt systems and basically only sells the CDC belt because of higher durability. You can check this out on their website. http://www.santosbikes.com
Cheers,
Robert
I’m aware of that! This is at odds with the 31,000km we did on our Centertrack belt. No complaints about that kind of durability here. 🙂
I road my Van Nic Amazon over the Passage du Gois the other day. Because it’s a tidal causeway the road was pretty slick with sand/salt and other unmentionables. Once on mainland France and dried out the belt just got noisier and noisier to the point that I stopped pedalling as Lycra clad pro’s approached embarrassed by the racket I was making! Once back at base a couple of buckets of water and some WD40 around the bottom bracket had me back in stealth mode. However it got me through thinking…..
1) would it be ok to use sea water to wash away excess grit/sand? I have a titanium frame so why not?
2) are the bottom brackets/cogs on belt drives any more susceptible to ingress from gritty material than chain options? i.e. Can I be sure that the whirring racket I made was actually the brake and not cogs/bearings?
The part of France I’m in has lots of unsealed, but fairly well compacted cycle tracks and I was just wondering if anyone had any quick and very portable cures for a potential whaling banshee?
I have a dual CDX belt drive on my Co-Motion tandem with 11,000km on it. I just noticed that as the crank revolves the belt tension increases and decreases significantly and at the exact same point each time in the rotation. Additionally, when the timing belt gets tight, the drive belt goes more slack and vise versa. Any thoughts?? Thank you for your time.
Hi Dan. I’ve found that you’ll have tight/slack points on both belts; it seems to be normal. Make sure you adjust your rear eccentric bottom bracket first so that the point of maximum tension is within the right range on your drive belt. Then adjust your front EBB to get the right tension at the tightest point on your timing belt. You should roll happy once you’ve adjusted them well. Alee
Sorry about the late reply here, GCB. I don’t see why you couldn’t use salty water to take off the grit, but I’d perhaps use fresh water and a toothbrush when you can to make sure it is properly cleaned. One of the commenters here suggested that silicone spray is the best way to keep your belt completely silent – I still haven’t tried it yet, but I can’t imagine it damaging a belt in any case. A clean belt + some silicone is my recommendation for tidal causeways!
Hi
I need some help.I’m a little green on the whole belt drive stuff but have got a Scott Sub speed 10 ( with eliptical bottom bracket) It has an Alfine 8 speed. I think as standard it comes with a 46T front and 24 rear. Now the tricky bit, I want to use this off road and want a couple of gears better than 1:1 ( on a standard set up ) , for those tough climbs. so my question ( I have no idea how to work it out) I realise i’d probably have to change over to cdx as the bike has cdc but what front and rear cogs and belt do I need?
I hope you can help
Hi Nic. The limitation here isn’t the belt, but rather the amount of torque the Alfine 8 is capable of handling. Shimano’s lowest permitted ratio is 1.9:1, which is precisely what comes on the Scott Sub Speed 10. But that of course doesn’t mean you can’t do it anyway. Have a play with the drive calculator at the bottom of this page by throwing in the ratio you want, and your chainstay length (456mm): http://www.gatescarbondrive.com/Tech/Overview#
Thanks for the Info Alee if I use a 32 front CDX and 28 Rear ( not sure what fitting the rear is on the Scott I guess its 9 spline?) That works out at chain stay of 456.45mm and give 1:143 gear ratio which I guess is as close as I’ll get? Does the gear ratio refer to the lowest gear I can get with that combo? also what are the issues around going below Shimano’s permitted torque? Thanks
The largest Alfine rear sprocket is 26t (http://www.gatescarbondrive.com/products/cdxsprockets).
With the Alfine hub and your current external gear of 1.9:1, you can already achieve the equivalent of a 1:1 ratio in your first gear. In your 8th gear, you are pushing the equivalent of 3.1:1. Shimano doesn’t permit any smaller gears because it is much easier to damage the internal parts with higher torque loads from the low gears. My suggestion is that if you’re going to push the limits, only do it by a little bit. Going to 1:1.1 is definitely pushing too far! 😉
I’ve just replaced my first sprocket at about 12,000 miles (20,000 km).
I’d tightened the belt as it was a bit loose and noticed it noisily minced the belt before I realised that the sprocket was completely worn and the residual teeth really sharp. I suspect I should have changed the sprocket when I changed the first belt maybe at half the mileage.
Front cog looks pretty good.
Getting the sprocket off was difficult and required a large pipe wrench on the sprocket.
Unfortunately the sprocket carrier came away with it. Note then that the hub leaks oil if tilted.
I presume that for each new sprocket you need a new sprocket carrier (70 euros and 40 euros respectively) unless you can separate the sprocket and the carrier?
This is the second belt I’ve been through, although at the moment I’m not sure how worn they need to be before replacement and am learning on the go.
I commute year round in pretty filthy conditions.
There seems to be little information to be had on the internet.
Hi guys,
I ride a – don’t laugh – Decathlon B’Twin Tilt 700 – I said don’t laugh! – folding bike with a carbon belt drive. I’m not sure whether its an own brand decathlon belt drive or something else.
Anyway I was using it happily for about 6 months without issue until I started to get these weird sounds – like the sound of a comb being run up and down the side of your finger? Others say it sound slike creaking or a squelching rubber. Whatever, it was making a sound and more to the point there was a slight vibration on the right pedal.
Then on one commute home, on a slightly steep incline the belt snapped completely. Decathlon replaced it but looked baffled as to why it was making the noise or why the belt snapped.
An independent bike shop looked into it and said that there was a buildup of dirt on the crank which was causing the belt to possibly slip? Does anybody else have any further ideas as to why this is happening and what I can do to prevent the noise and damage to my new belt?
Hi Prestwick
There are a few things that you can do:
– Keep the belt and cogs clean – you can use silicone spray as a lubricant too if need be.
– Make sure the belt isn’t over tensioned. Rotate the crank all the way around, checking for tight spots.
– Check the belt is aligned well. I’ve experienced the comb-on-fingers sound on slightly out of line belts. If it looks like the belt is pushing towards one side, you can add or remove bottom bracket spacers (or chainring spacers) to get the right spacing.
Alee
Hi Alee,
Congratulations on such an informative site. Very refreshing! I have a couple of CDX related questions that i was hoping to get answers on. I really hope you can help. Im off on my 4th long European tour imminently on my Koga/Rohloff/Gates setup. Very happy with the system so far but as i plan to be away much longer this time ( 6months+ ) i am thinking to take a spare belt with me just in case. My first question is: If coiled up correctly can the belt just live in my pannier for months on end without it affecting the carbon fibres?
My second question is: In the event of a problem with any part of the Gates Drivetrain what would you recommend to be the best course of action whilst on tour, contact gates? Search for the nearest Bike shop that deals with Belt driven bikes? Like most long distance tourers using new technology my paranoid mind envisages me high in the mountains in a remote region of a country not reknowned for having good bike shops, with a failed Drivetrain! Any tips would be greatly appreciated. I know i should have faith in the technology but i also like to have backup plans at least half thought out before i go.
Thanks for your time. I hope to hear from you very soon as i leave in a couple of days.
All the best ………………………..
Hi Tom
Thanks for the kind words!
I kept three belts (two standard and a tandem belt) in the small inside pockets of my Ortlieb panniers on my multi-year adventure. I only got to use a spare for the last 1000km in the end, but better safe than sorry! With them folded up in a bag, it’s pretty hard to bend them so much you damage the fibres.
With regards to damaged drivetrain, I honestly wouldn’t worry. The rear cog is made out of stainless steel and I can’t even imagine what it would take to damage it. The front chainring is made out of some pretty solid aluminium – mine took some hits when lifting my bike over things, without any consequence. If you wanted to feel at ease, take a spare chainring, but remember that it’s pretty easy to get stuff posted within Europe.
Have a great trip!
Alee
Hey Alee
Thanks for such a swift response. I still haven’t heard back from gates regarding the same questions. It’s great to get real world advice about the technology from the touring perspective as the Internet can generally be a bit of a minefield when you’re looking for a very specific answer to something. Nobody around where I live, bike shops included, have even heard of gates! So thanks for putting yourself out there as a willing resource
I enjoyed very much your Co-motion/pinion article and the whole “basically please just give me one” undercurrent! In a way I kind of want bike drivetrain technology to slow down a bit so I can enjoy my rohloff for longer before the inevitable purchase of a pinion!
Anyway, 3 spare belts! I thought I was mental taking just one. Now I will take one without fear. Sorry to take up your time but I hope you could answer just a couple more questions for me?
1) i watched the gates video on how to coil up a belt ( mine came flat ) and although it looks simple enough they do make you feel that if you do it even slightly wrong then not only will your belt crumble to dust but your whole touring setup will explode and you will die alone in a ditch. You got any pointers on coiling it up?
2) regards tight spots on the belt gates say that anything significantly over a 10-15hz difference between lowest and highest frequency reading when using the app, means the front ring will need centering or something. I can get discrepancies of 25hz when checking the tension, but the belt is quiet, doesn’t jump and seems to perform as it should. Do you think I should just leave it and have faith? In back to back tension tests (out of sheer curiosity) before and after riding i take a frequency reading every quarter turn of the crank until the whole belt has been covered and it always gives me an average of 45hz. I called Velorution ( uk main distributor for gates ) about how to best use the app and they said they don’t even bother tension testing anymore! They simply press down on the belt and without excessive force it shouldn’t move more than 10mm. It all sounds a bit vague these tensioning issues. I don’t want to buy a tension gauge device and I have a feeling you’ll probably be of the opinion that if it’s performing well then just leave it alone! Just wondering what your thoughts are on this.
well that’s a very long post, sorry!
All the best to you and hope to hear from you soon, tom from Devon uk.
Hi Tom
When I was researching belts myself, there was nothing out there. So I decided to just create all the content myself! That’s how most of the stuff on this site ends up being here… 🙂
Coiling a belt should feel natural. Just twist it into a figure eight, and it should naturally want to go into a coil. The main thing you need to be aware of is that if you ‘kink’ the belt at any time, the carbon can be compromised. That’s pretty hard to do when coiling it up.
With regards to tension, I tend to agree with Velorution in that you can easily go by feel – 10mm seems about right! You will find tight spots in your drivetrain, and getting the front chainring as centred as possible will minimise those. Once I’m within a range where the belt feels light, but not loose, I only tension my belt if I experience slippage on the rear cog. So basically, you don’t need a gauge!
Alee
Thanks so much alee, your advice is very much appreciated and reassuring. Gates got back to me about coiling the belt up and a guy from gates Europe even made a quick video of him coiling and Un-coiling a belt, slamming it down onto the table after each coil and doing it very fast. I guess they’re not made of egg shell after all!
They didn’t get back to me about the best course of action to take in the event of needing spare parts/repairs etc though. I guess I just call gates Europe in Germany and take it from there. Out of interest, if you were in Europe and needed gates assistance, who would YOU call? ( except the ghostbusters of course ) .
All the best once again
Tom
I’d probably place an order for new parts through Bike24 for the quickest turn around. https://www.bike24.com/1.php?content=13&search=gates+carbon
If it’s a genuine warranty issue though, Gates Europe should be able to help you out!
I love my quiet belt but I was wondering if it is normal to have a little play before the belt engages?
All of mine engage straight away. I don’t think that’s normal!
Hi Alee,
Great post but some of the things you wright down aren’t completely correct. The price of the CDC is still a lot lower. In the EU for a cog it’s about €30 lower in price, in total you pay about €100 less than the CDX version.
At our bike shop we sell and maintain both systems equiped with Rohloff. We do sell Santos bikes, Surly and our own Titanium brand. What we noticed in these couple of years is that the CDX wears out a lot faster than the original CDC. Even with the renewed CDX belts and cogs.
We do have customers who can put a lot of milage with the CDX version but the CDC version still wins this. Only problem with CDC is that your frame has to be stiff enough to keep the belt turning nice, straight and smooth.
Millage done with the CDC version without breaking: 41 000 km (only replaced to keep a safe riding)
Also Santos bikes has done long term tests of both systems right now with some bike travelers like the bicycle junkies. They came to the same conclusion with their belts.
One note, when you put to less tension on the belt for the CDX than the cut out between the teeth wears out very very fast within several km’s you can completely ruin your belt. That didn’t happen with the CDC belt, you will have a faster wear out, but the CDC wil slide form it’s chain rings and riding is over so you know you have to put more tension on it.
We do still prefer CDC at our shop, even with the new CDX version of the belt and yes even for offroad riding… I may suggest that you look at the bike’s specs. Stiffness of frame is one important factor to decide between CDC or CDX.
So at the price point your article isn’t correct, at the point of tear and wear. Maybe, but we see different facts.
One advice, when you decide to change the belt after it’s wear out than we advice to change the cogs as well. A slightly worn out cog makes the belt wear out much much faster (so there won’t be a profit in comparison with chains any more), when you change the whole setup you can ride safely a lot of millage without thinking of your setup when installed correctly. It will cost you some money, but you will be very happy when doing this.
Cheers,
Koen
Why is not possible or, at least, usual to put a dynamic tensioner for the belt as well as for chain drive? I think that it should be more eficient that apply so much preload.
Thanks!
I don’t know for sure, but I’d say that it has to do with belt tension. The Carbon Belts need to be very tight!
Hi Koen
Thanks for providing your experience! This article is due for an update, so your comments are very timely. The update will include current pricing (which is lowering with time).
I find it quite interesting that Santos has found the opposite to my observations with regards to belt longevity. I can’t argue with their findings or yours – I can only provide my own experience. Maybe I should switch back to the CDC belt again to see if I can get better milage?
Alee
Sounds like there are significant issues remaining with this technology. 🙁
Special frames, tight-tolerances, excessively sensitive to environment,
and finally… expensive. The constant cleaning, to me, implies that
maintenance is higher in some cases than for a conventional chain-type drive.
Also, when was a properly maintained chain loud? I think a lot of people hear their worn out/misaligned rear mech and think that’s the chain! All I hear on my bike is wind noise. Joggers too–had to install a bell. Same for the tandem.
Getting 31k-KM out of a belt would be the equivalent to just 2 chains
for me. I replace chains at 0.75% with a CC-3.2, and have yet to need to
replace cogs or chain rings. That’s only about $100(usd) of chains…
adding the lube would be, at most, an additional $40 or so. (and that’s a lot of lube, doubt I use that much!) That’s about $150 (USD) for 31kKM. The belt is about $75 (again USD)… so less than $75 in savings matched to the chain-setup.
However, there are significant problems with the rest of the belt-system’s drivetrain technology… cogs and rings don’t seem to routinely outlast the second belt… so, in total.. the belt systems are _much_more_expensive_ than chains to maintain… however, if we isolate to just chain and belt costs, there is about a $75 advantage… until you have to scrap the whole $300+ system and start over–assuming you don’t destroy your IGH… which appears to be a fairly common victim of belt problems.
I think the lessons learned from belt drives in the motorcycle-world may also be applicable… they also complain of noise and their belt life is only about 2x that of a chain… and the repairs are equally expensive when they get sand in their drives… which seems to match what I read here… Although, a lot of belt driven motorcycles get far less travel distance than my pedal-bike does.
So, for the low-mileage crowd, the belt may make good sense?
It is interesting to see people here seems to prefer the newer CDX Centertrack over the original CDC Mudport belts and sprockets.
I have two bikes with both belts and love the CDC more than the CDX as the CDX once a while makes noise because it seems the centre of the sprocket touches the belt. Never experienced that for the CDC.
That is only one observation but here in the Netherlands, most of the professional bike builders seems to favor CDC over CDX, see for instance Riemaandrijving on santosbikes.com
The Gates belt system is obviously not for you.
Really sorry for the late reply. Thanks very much for your advice and suggestions. Unfortunately in the last 2 years life has got in the way and this project has not progressed, but it will hopefully do so soon.
I am thinking about changing out my CDC on a Scott Sub 10 to CDX as I have cracked the rear sprocket after about 4000 kms and the belt won’t stay on. Is it possible to put spacers on the rear axel on the Alfine instead of the crank? The front sprocket is close to the frame already.
Hi Greg, I think you will have interferences with the frame, but from a functional point of view there’s no drawback for adding some spacers.
My wife has a CDX on her Trek Soho that the Gates calculator says should fit and it has a faster gear ratio (2.5) than mine (1.9) which I would love to change as it is generally flat here. Going to see if it will fit before I buy. In the meantime my LBS put a chain on for only $50CND, so as for the cost comparison for me the chain wins, but I will go back to a belt for the low maintenance, no worry about calf tattoo when I get to work, and the superficial appearance of the red CDX belt on my red and white Scott.
Nic,
Did you upgrade to CDX? I cracked my back CDC sprocket and would like to upgrade but it’s flat here so I want to go from 1.9:1 to 2.5:1 as I never go below 4th. FYI for others reading this the Alfine 8 is 1:1 in 5th.
Salve, posso chiedere: quanto sono limitato nel numero dei rapporti tra cinghia e catena con Roholoff?
Per grandi salite, viaggi in zone montuose è meglio belt o chain su Roholoff?
Quali aziende producono telai compatibili per cinghia roholoff? Quali mi consigliate?
Soma Wolverine, SURLY ECR, altri, and?
Grazie,
Alberto.
Hello,
The snub wheel on my carbon belt has just given up the ghost, Near as I can figure there were two ball bearings held in place by spring. what I can’t guess at is how this spring was held in place as the retaining hole has no sign of cap and there are is no sign of threading for a possible holding bolt. I have searched the internet but can find no where to buy a replacement wheel kit.
I bought a new Marin Fairfax SC4 with the gates belt drive. I’ve only ridden about 1800km on it, but one of the teeth has broken off the back sprocket already. It kind of looks like the belt doesn’t fit the sprocket right, like a stretched chain, but I don’t see how that could be. Any idea what would cause a tooth to break off? Is the belt too loose? The dealer told me not to tighten it anymore then they had it.